Learning the Basics of Plumbing for Bathtub Installation
Click HereWe've found this article relating to Installing A Bathtub directly below on the internet and reckoned it made sense to talk about it with you over here.
Setting up a tub isn't specifically rocket science, however it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a new one is additionally a moderately tough project. If the old bathtub is easily available, the project can move immediately; if you need to open up a wall surface to eliminate the old tub as well as place the new bathtub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the brand-new one. Make certain you have certified on your own for the task as well as are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is better to think about using one before you begin. Opportunities are you might need an expert plumber to make tube connections.
This post will aid you set up a new tub in your washroom if you have actually currently bought a new bathtub and do not need to transform the arrangement of your previous supply of water pipes.
Your tools and also material list must comprise the following:
Planning for the Installment
First of all, the sustaining framework provided with the bathroom needs to be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets system to stop pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of removing the existing taps can be rather troublesome because of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the remaining water that will come from the pipes. Once the supply pipelines have been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Making use of both wood boards under its feet, place the tub in the called for placement. The wooden boards are practical in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the bath tub up until the level reviews degree.
To set up faucets, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also check all joints and new pipework for leaks and also tighten them if necessary. Fill up the bath tub as well as additionally examine the overflow electrical outlet and also the typical outlet for leakages.
Ultimately, repair the bath paneling as described in the maker's instruction manual. Tiling and securing around the bathtub must wait until the bath tub has been utilized at the very least once as this will certainly settle it right into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Protect the tap in place with the supplier supplied backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind should be linked to the tap finishes initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall surface between the bathroom and also the tiling, causing problems with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, as well as can sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill up the tub with water prior to sealing, to allow for the motion experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not think about this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub Yourself? Put a review further down. We would be interested to hear your responses about this post. Hoping to see you back again soon. Those who appreciated our blog entry plz do not forget to pass it around. We cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
High-quality emergency response guaranteed.